If you want to learn more, please visit our website Self-Leveling Compound Manufacturer.
&#;Self-leveling underlayment&#; (SLU) is a bit of a misnomer. Although this type of product is incredibly useful, it does require a thoughtful installer to ensure the best results. Follow these guidelines to prevent issues in your self-leveling underlayment installation.
Select a product appropriate for the installation: Know your installation environment and familiarize yourself with the relevant ASTM standards for strength. A commercial floor subject to heavy rolling loads will require a higher-grade self-leveling underlayment (like TEC® Level Set 300 Self-Leveling Underlayment) than a floor in a single-family home.
Also, it is critical to understand your project timeline and choose a product that fits within the appropriate schedule. Some products may require 24-48 hours prior to installing floor coverings while other more premium products are ready to accept moisture-sensitive floor covering in 12 to 16 hours.
Consult product data sheets for information on tensile strength, compressive strength and flexural strength, as well as recommended cure times.
Generally speaking, there are two types of self-leveling underlayments &#; traditional and next generation technologies. The most noticeable difference between traditional and next generation SLUs are the flowability and the smooth surface profile of each product. Check out TEC's new high-flow SLU: Level Set 500 HF and for best practice tips for successful high flow SLU installations view our Technical Bulletin.
Some installers prefer the attributes of traditional SLUs because of the working properties. Others prefer the new technology for its high flow properties and extended working time.
The job scope will dictate which product technology should be used for installation. Traditional SLUs work best for deep fill applications greater than 3/16&#;. The newer technologies are ideal for thinner applications.
Know your substrate: Most SLUs require that all surfaces are fully stable and structurally sound prior to the application of a self-leveling underlayment. For example, understanding your existing substrate porosity is critical to choosing the proper primer. (A simple water droplet test will determine the surface porosity per ASTM F). Equally important is to know the make-up of the existing substrate. For example: typically, sound concrete requires a single coat of primer. Unsealed Gypcrete may require additional steps, including multiple coats of primer prior to the application of cement-based self-leveling underlayment.
Prepare your substrate: Make sure to plug all floor openings, gaps and cracks and install termination dams to prevent any seepage. Consult with product manufacturers to determine moisture limitations of the floor covering, self-leveler, and adhesives to determine if moisture mitigation is needed.
If moisture mitigation is required, this must be done prior to installation of the self-leveling underlayment.
For more acrylic emulsion styreneinformation, please contact us. We will provide professional answers.
Self-leveling underlayments require the use of a primer prior to installation (like the TEC Multipurpose Primer). Failure to use product recommended primer may result in installation failure. Primer retains the moisture within the self-leveling underlayment to allow proper curing. Secondarily, it acts as a bonding agent to ensure the SLU bonds properly to the substrate. Refer to the primer label for information regarding application methods and dilution per ASTM F.
Beyond priming, most self-leveling underlayments require that the substrate is free from any contaminants that may inhibit bond, including adhesive residue, sealers/curing compounds, oil, grease, loose or peeling paint, or other contaminants. Polished underlayments will require epoxy primers and/or a specific Concrete Surface Profile (CSP), and in these cases, mechanical abrasion (shot-blasting), is required.
Proper water demand: Mix your self-leveling underlayment within the water range specified on the bag. Overwatering will lower the strength of the underlayment and may cause cracking and disbonding. Additionally, a white film may form on the surface of the cured underlayment if the product is overwatered. Failure to properly mix the SLU may make it difficult to work with and lead to improper flow, cracking, or an irregular surface. Mix a minimum of two bags at a time when barrel mixing to ensure optimum efficiencies during the application process. In addition, some SLUs can be pumped. If pumping, special attention is needed to maintain proper water ratios and prevent overwatering. Follow equipment and product manufacturer&#;s recommendations when pumping self-leveler.
Product and ambient temperature: Make sure that the temperature of the room is within the manufacturer&#;s acceptable range. A climate that is too cold or too hot can affect the product, such as increased set time in cool temperatures or reduction in heal time in hot environments. Temperature and humidity will affect flow, working time and set time of the SLU.
Additionally, the temperature of the powder and the water is crucial. Leaving product in the sun, or in a hot environment may lead to flash setting. In situations where warm product is unavoidable, mixing with cold water may help combat installation issues. To maintain cold water temperatures in hot conditions, use blocked or bagged ice in your water barrel.
Whether the environment is warm or cool, acclimating the product prior to mixing is always a best practice.
Use as recommended: Manufacturers will specify the maximum thickness of their product. Some products allow for the addition of aggregate (pea gravel) to increase the depth of the pour, while others only allow their product to be used neat. Be sure to use the appropriate aggregate size and amount when extending a self-leveling underlayment in a single pour. Two separate pours or multiple lifts will achieve the target thickness without the use of additional aggregate. Once the SLU from the first pour becomes a walkable surface, you may proceed to apply the proper primer coat for the additional pour or lift. If a surface is extremely uneven in isolated areas with depressions greater than ½&#; deep (bird bath), you may treat these areas independent to the final pour. This will assist with the application process by using a consistent amount of self-leveling underlayment throughout the application. Always consult with manufacturers to determine the most suitable product for your application.
Protect your freshly poured underlayment: All self-leveling underlayments should be protected from direct air movement (drafts) during the initial curing process (2-6 hours) as they may cure prematurely which leads to cracking. Generally, most underlayments are not considered final wear layer surfaces. During the final curing process (2-24 hours) they should be protected from excessive construction. Traffic without protection can lead to gouging and irregular surfaces. Allow to cure completely to prevent any unnecessary surface damage, prior to the floor covering installation.
A common theme connects these successful self-leveling underlayment application guidelines: noting and adhering to the manufacturer&#;s instructions. You must read labels and product data sheets carefully to ensure products perform as desired.
Make sure to check out our entire line of Surface Preparation products. If you need assistance determining which product is right for your job, contact our Technical Support team here or by calling 1-800-832-, Mon-Fri 8 a.m. - 6 p.m. CST.
For more information, please visit polycarboxylate contractor.